Home » News » Industry knowledge » MSZ15-312 ,MSZ15-340,MSZ15-350,MSZ15-375, MSZ15-406 interlocking cold formed sheet pile

MSZ15-312 ,MSZ15-340,MSZ15-350,MSZ15-375, MSZ15-406 interlocking cold formed sheet pile

Inquire

The cross section of the middle light thin slice. The wire rope used for a scaffold should be able to support six times the predetermined load of the MSZ15-350. Bank or sheet piles suppliers sloping scaffolding is prohibited. All joints in the film should be welded to prevent leakage. Bin fill should be 8 inches thick loose elevator and the maximum MSZ15-340 shall be compacted to 95% Procter standard gauge density.Narrow support (30 inches wide). No working platform should be erected above 4 feet unless equipped with extension support. It is not allowed to pass through saturated compaction.

Contrary to popular believe, Cold Formed Sheet Piles to give very respectable water tightness. Though in most cases, water conductivity in Hot Rolled Sheet Piles are still lower than Cold Formed Sheet Piles, Mer Lion Metals can always supply piles with waterproofing membrane pre-injected in the factory without the hassle of it being done on site. This membrane is called Wadit and it is by far the most superior type of waterproofing method made specifically for the sheet piling market.

Zee Mega 15 steel sheet pile shall be placed MSZ15-375 and MSZ15-406 thick loose lifts and compacted to the maximum stress standard Procter minimum 90% density.Scaffolds should be supported, and support appropriate length, making the scaffold will keep vertical and rigid. All of the listed medium MSZ15-312 lightweight sheet piles are fully manufactured in the United States. All middle light sheet piling can be cut to the length you need.

The linked sheet pile MSZ15-312 MSZ15-340 is not big enough to be labeled MSZ15-350, with the danger of waterproof sealant word "hole" or "cover", it should be marked with high visibility paint warning recognition. If MSZ15-406 is required to remove the cover, the display will remain at the opening until the cover is replaced. The surveyor should recommend persons entering the dangerous area to prevent exposure to dangerous areas, but not to carry out other tasks.

Sectio	Dimensio	Ma	Moment of inertia	Modulus of sectio
	Width	Height	Thickne	Pile	Wall
	w	h	t/
	I	I	I	Lbs/ft	Lbs/ft2	In4/ft	In3/ft
MSZ10-312	38.82	2.19	0.312	49.72	15.37	1.3	0.67
MSZ10-340	38.82	2.19	0.340	54.10	16.72	1.41	0.72
MSZ10-350	38.82	2.19	0.350	55.69	17.22	1.45	0.74
MSZ10-375	38.82	2.19	0.373	59.67	18.45	1.56	0.79
MSZ10-406	38.82	2.19	0.406	64.60	19.97	1.73	0.86
MSZ11-312	38.55	3.53	0.312	49.72	15.48	6.83	3.76
MSZ11-340	38.55	3.53	0.340	54.1	16.84	7.43	4.06
MSZ11-350	38.55	3.53	0.350	55.69	17.34	7.65	4.17
MSZ11-375	38.55	3.53	0.375	59.67	18.58	8.21	4.44
MSZ11-406	38.55	3.53	0.406	64.6	20.11	8.92	4.79
MSZ12-312	37.72	6.64	0.312	49.72	8.76	29.29	8.76
MSZ12-340	37.72	6.64	0.340	54.1	9.50	31.87	9.50
MSZ12-350	37.72	6.64	0.350	55.69	9.77	32.84	9.77
MSZ12-375	37.72	6.64	0.375	59.67	10.43	35.17	10.43
MSZ12-406	37.72	6.64	0.406	64.6	11.27	38.16	11.27
MSZ13-312	36.38	9.58	0.312	49.72	14.13	67.86	14.13
MSZ13-340	36.38	9.58	0.340	54.10	15.32	73.79	15.32
MSZ13-350	36.38	9.58	0.350	55.69	15.74	75.93	15.74
MSZ13-375	36.38	9.58	0.375	50.67	16.81	81.34	16.81
MSZ13-406	36.38	9.58	0.406	64.6	18.18	88.27	18.18
MSZ14-312	34.56	12.24	0.312	12.27	19.62	120.97	19.62
MSZ14-340	34.56	12.24	0.340	18.89	21.29	131.28	21.29
MSZ14-350	34.56	12.24	0.350	19.34	21.91	135.50	21.91
MSZ14-375	34.56	12.24	0.375	20.72	23.38	144.93	23.38
MSZ14-406	34.56	12.24	0.406	22.43	25.29	157.25	25.29
MSZ15-312	32.79	14.11	0.312	49.72	18.20	172.66	24.24
MSZ15-340	32.79	14.11	0.340	54.10	19.80	187.52	26.27
MSZ15-350	32.79	14.11	0.350	55.69	20.38	193.26	27.06
MSZ15-375	32.79	14.11	0.375	59.67	21.84	207.03	28.91
MSZ15-406	32.79	14.11	0.406	64.60	23.64	224.46	31.27
MSZ16-312	31.05	15.54	0.312	49.72	19.22	223.36	28.45
MSZ16-340	31.05	15.54	0.340	54.10	20.91	242.98	30.88
MSZ16-350	31.05	15.54	0.350	55.69	21.53	249.85	31.74
MSZ16-375	31.05	15.54	0.375	59.67	23.06	267.87	33.95
MSZ16-406	31.05	15.54	0.406	64.60	24.97	290.74	36.75
MSZ17-312	29.71	16.43	0.312	49.72	20.09	262.34	31.60
MSZ17-340	29.71	16.43	0.340	54.1	21.86	285.10	34.27
MSZ17-350	29.71	16.43	0.350	55.69	22.50	293.36	35.25
MSZ17-575	29.71	16.43	0.375	59.67	24.11	314.57	37.71
MSZ17-406	29.71	16.43	0.406	64.60	26.10	241.03	40.80
MSZ18-312	28.38	17.2	0.312	49.73	20.58	296.05	34.49
MSZ18-340	28.38	17.2	0.24	54.1	22.39	322.09	37.45
MSZ18-350	28.38	17.2	0.350	55.69	23.04	330.95	38.46
MSZ18-375	28.38	17.2	0.375	59.67	24.69	354.49	41.12
MSZ18-406	28.38	17.2	0.406	64.6	26.74	384.83	44.53
MSZ19-340	26.88	17.9	0.340	54.1	23.61	368.18	41.17
MSZ19-350	26.88	17.9	0.350	55.69	24.30	867.04	42.24
MSZ19-375	26.88	17.9	0.375	59.67	26.04	929.74	45.25
MSZ19-406	26.88	17.9	0.406	64.60	28.19	1008.15	48.97