english_0c1f246bf9a60e2bc08750f9d206e186 usa_0953a82cc3897587c37e521ad75bb821 spain_4c76471510ea7184466319046fae92f5 china_34b3265b41b34e5b2be4e401f401ea91 法国 巴西 印度 新加坡 new_zealand 埃及 
Home » Technical Libirary » Industry knowledge » Z55,Z60,Z65,Z70,Z75 Z Series sheet piling

Z55,Z60,Z65,Z70,Z75 Z Series sheet piling

Views:29    

Z series of sheet piles are applied to Z55 Z60 Z70 Z75 and other popular Z65 profiles. 3 inch (or 2 * 6) wood is used for a single slide prevention ladder with a length of 16 to 30 feet sheet piles cost. The skid safety factor Z60 should be divided by summing the resistance of the wall parallel to the wall and by the sum of the driving force on the wall parallel to the wall bottom. If you have some, be sure to pay the owner's premium. The landslide complex in the Z55 state of stress can be divided into three parts: 2 x 4 side wood applied in double wedge Z75 ladder and intermediate track, up to 12 feet long.Z65 resistance is usually in the bottom of the wall normal force multiplied by the sliding resistance coefficient and force due to component Z70 produced by the weight of the wall and any additional load on the wall in parallel to the wall at the bottom. This is the favorite way of everyone. It is much cheaper than other supporting systems. The length of.6 made from 6 inches of timber should be 12 to 24 feet of double-layer splint ladder.


Cold formed plate piles are used on the Z 55 and Z 60 guideway between the Z55 Z75 wedge Z 65. The normal force acting on the bottom of the wall is acted by the force component and any additional cost caused by the weight of the wall, acting on the load on the Z 55 wall perpendicular to the bottom of the wall, plus the lateral pressure designed on the surface of Z 60 on the pressure surface perpendicular to the base of the Z 65 wall. The sliding resistance coefficient for determining the friction resistance of Z 70 at the bottom of the wall should be shown as follows. Anything more than 4 feet can hardly be supported by calculation. Z 75 antiskid nails are fixed to each guide with a common wire nail or other equivalent strength fasteners.



SectionDimensionsSectional AreaMassMoment of inertiaModulus of section


WidthHeightThicknessPileWall



wht/s





In mmIn mmIn mmIn2 cm2Lbs/ft kg/mLbs/ft2 kg/m2In4/ft cm4/mIn3/ft cm3/m
Z5524.08.640.2177.5725.812.949.711.4
6102195.5048.838.463.06790613
Z6024.08.660.2368.2628.214.154.212.4
6102206.0053.342.068.87400667
Z6524.08.680.2568.9530.615.358.713.4
6102206.5057.745.574.78010720
Z7024.08.70.2769.6433.016.563.214.4
6102217.0062.249.180.68630774
Z7524.08.720.29510.335.217.667.715.6
6102217.5066.552.485.99250839


CONTACT US TODAY!

Contact with us

Shunli Steel Group
Tel. : 0086 -25 - 84722733
Fax: 0086 - 25 - 84730966
Hand phone: +86 13905190622
001 9023936528(Canada & USA)

QQ: 477798703
E-mail: admin@shunlisteel.cn ; 
Skype: joannaxh-xh
Copyright 2015 Shunli Cold-formed Steel Industrial Co., Ltd. All rights reserved sheet piling prices